EXACTLY HOW TO REMOVE AND ALSO REPLACE A BATHTUB

Exactly How to Remove and Also Replace a Bathtub

Exactly How to Remove and Also Replace a Bathtub

Blog Article

Instant Quote

What are your thoughts with regards to How to Install a Bathtub Yourself?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a bath tub isn't exactly brain surgery, yet it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately tough project. If the old tub is conveniently accessible, the job can relocate quickly; if you have to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's abilities, although you will require an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to consider using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This article will aid you install a new tub in your washroom if you have already gotten a brand-new tub as well as do not require to change the plan of your previous water system pipelines.
Your devices and material list need to comprise the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Preparing for the Setup


    First of all, the sustaining frame supplied with the bath must be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
    Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the supplied washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its final setting.

    Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted accessibility that is usually the situation.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
    Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

    Installing the Bath tub


    Utilizing the two wood boards under its feet, place the bath tub in the needed placement. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
    The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the level reviews level.
    To set up faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
    Activate the water supply as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the tub as well as also check the overflow electrical outlet and also the normal outlet for leaks.
    Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and also sealing around the bathtub must wait till the bath tub has been used a minimum of once as this will certainly resolve it right into its last position.

    Fitting New Taps


    If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the existent supply pipes.
    If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type ought to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling listed below.
    You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break rather very early if you do not consider this movement prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or water-proof sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    As a passionate reader about How to Install a Bathtub Yourself, I was thinking sharing that piece of content was a good thing. Feel free to set aside a second to share this blog entry if you enjoyed it. Thanks a lot for your time invested reading it.




    Get An Estimate


    Report this page